fix(autocal): 校验运动单位并等待命令成功后判断到位

阻止单位不一致的姿态命令，避免提前到达的位置快照误报成功或推进下一轴。
相关检查 164 项通过，2064 组目标及 8256 条运动调用与原基线完全一致。

apps/autocal/docs/motion-unit-contract.zh.md

@@ -12,7 +12,7 @@
 
 [`PoseMover`](../src/orisys_autocal/motion/pose_move.py) 启动前检查计划中的轴编号、物理目标和已换算的用户单位目标仍对应当前配置。工作线程执行前再次读各目标轴的 `UNITS`，全部校验完成后才按原顺序发送原绝对目标。配置或角色映射在排队期间改变时，旧计划被拒绝，要求重新规划；不会偷偷套用新设置。
 
-移动器按命令 token 接收工作线程的拒绝或失败，立即标记该次移动失败，不再靠后续位置恰好相同判定到位。其他命令的结果不会取消当前计划；界面继续使用已有的移动失败处理和停止路径。
+移动器按命令 token 等待工作线程确认成功，然后才用随后收到的位置快照判断到位或推进下一轴；等待期间仍检查报警及读取失败。提前收到的位置快照不缓存重放。对应命令被拒绝或发生异常时立即标记失败，其他命令的结果不解除等待；界面继续使用已有的移动失败处理和停止路径。
 
 执行前增加的是只读参数检查，可能增加通信延迟，不保证与旧版完全相同的发送时刻。控制器被其他软件在最终读取和运动指令之间改动的并发窗口，本次也不能消除；操作期间仍需保证设备配置的单一写入者。
 
@@ -29,8 +29,8 @@
 
 ## 验证与限制
 
-回归测试见 [`test_motion_unit_guards.py`](../tests/test_motion_unit_guards.py)。它覆盖既有五轴命令的确定数值和顺序、配置一致的线性换算、异常读回、旋转标定条件、排队期间配置改变、读取失败时整组零发送，以及原始单位调试移动的兼容性。现有测试夹具补充了真实流程所需的单位观测，没有降低断言或放宽限位。
+回归测试见 [`test_motion_unit_guards.py`](../tests/test_motion_unit_guards.py)。它覆盖既有五轴命令的确定数值和顺序、配置一致的线性换算、异常读回、旋转标定条件、排队期间配置改变、读取失败时整组零发送，以及原始单位调试移动的兼容性。另覆盖分步/整组的快照先于命令结果、拒绝及异常、token 匹配、逐轴确认与等待期间故障。现有测试夹具补充真实流程所需的单位观测和成功回调，没有降低断言或放宽限位。
 
 修改前从本地 design 导出保存 1032 顶点，使用默认安装与当前偏好配置，共 2064 组姿态和规划目标。修改后逐元素严格相等，最大差值为 0；使用修改前源码与当前源码在记录型 DemoTransport 上分别执行相同计划，产生的 8256 条绝对运动调用也完全一致。这验证软件输出保持，不构成实机轨迹或物理接触精度证明。
 
-最终相关检查 136 项通过；Autocal 全套为 720 项通过、3 项失败，无跳过。两项模拟采集失败及一项旧 scratch 路径假设与原始审查记录一致，本轮没有修复。回归测试在修复前复现单位风险，移除当量一致性判断的内存变异也被检出。详细结果见[架构审查](../../../../docs/workflow/autocal-architecture-review.zh.md)。证据位于 app `.scratch/autocal-unit-guards/`，不属于长期归档。
+首次单位防护验证为 136 项通过，Autocal 全套为 720 项通过、3 项失败。后续审查发现位置快照可能先于命令结果，提前误报成功；2026-10-18 增加上述确认门槛后，相关检查 164 项通过，原实现被新增测试检出 7 项失败。全套结果及限制见[架构审查](../../../../docs/workflow/autocal-architecture-review.zh.md)。证据位于 app `.scratch/autocal-unit-guards/` 与 `.scratch/autocal-command-ack/`，不属于长期归档。

apps/autocal/src/orisys_autocal/motion/pose_move.py

@@ -31,11 +31,10 @@ import time
 from collections.abc import Mapping, Sequence
 from dataclasses import dataclass, field
 
-from PySide6.QtCore import QObject, Signal
+from PySide6.QtCore import QObject, Signal, Slot
 
 from .models import MotionResult, Snapshot
 from .service import LINEAR_ROLES, MotionService
-from .units import user_units_to_deg
 
 #: How close an axis must be to its target before the next one starts, per unit:
 #: millimetres for the linear roles, degrees for the rotary ones. One user unit is
@@ -141,6 +140,33 @@ class MoveStep:
         return f"{self.role} {self.target:+.4f} {self.unit}"
 
 
+def _check_steps(
+    service: MotionService, steps: Sequence[MoveStep], *, refresh_units: bool = False
+) -> MotionResult | None:
+    """Reject stale axis/scale bindings; never reinterpret an existing plan."""
+    refusal = service.check_axes_move(
+        {step.role: step.target for step in steps}, refresh_units=refresh_units
+    )
+    if refusal is not None:
+        return refusal
+    for step in steps:
+        if step.axis != service.role_axis(step.role) or step.units != service.to_units(
+            step.role, step.target
+        ):
+            return MotionResult.refused(
+                f"{step.role} 的轴映射或单位已改变，请重新规划 / axis mapping or units changed; replan"
+            )
+    return None
+
+
+def _execute_steps(service: MotionService, steps: Sequence[MoveStep]) -> MotionResult:
+    """Worker-only read check, then the original absolute targets in their order."""
+    refusal = _check_steps(service, steps, refresh_units=True)
+    if refusal is not None:
+        return refusal
+    return service.move_abs_many(tuple((step.axis, step.units) for step in steps))
+
+
 @dataclass(frozen=True)
 class MovePlan:
     """A sequence of steps, and what it is for."""
@@ -254,6 +280,7 @@ class PoseMover(QObject):
         self._service = service
         self._submit = submit
         self.state = MoveState()
+        self._command_token: int | None = None
 
     # ------------------------------------------------------------------ control
 
@@ -271,9 +298,7 @@ class PoseMover(QObject):
         """Validate and begin. Refusal is returned, not raised."""
         if self.running:
             return MotionResult.refused("已有运动在执行 / a move is already running")
-        refusal = self._service.check_axes_move(
+        refusal = _check_steps(self._service, plan.steps)
-            {step.role: step.target for step in plan.steps}
-        )
         if refusal is not None:
             return refusal
         if not plan.steps:
@@ -312,19 +337,21 @@ class PoseMover(QObject):
         if not step.units == step.units:  # NaN: no calibration for this role
             self._fail(f"{step.role} 无法换算成用户单位 / cannot convert {step.role}")
             return
-        self._submit(lambda service, step=step: service.move_abs(step.axis, step.units))
+        self._command_token = self._submit(
+            lambda service, step=step: _execute_steps(service, (step,))
+        )
         self.stepStarted.emit(step)
 
     def _issue_together(self, plan: MovePlan) -> None:
         """Command every step in one worker call."""
-        moves: list[tuple[int, float]] = []
         for step in plan.steps:
             if not step.units == step.units:
                 self._fail(f"{step.role} 无法换算成用户单位 / cannot convert {step.role}")
                 return
-            moves.append((step.axis, step.units))
         self.state._group_idle = {}
-        self._submit(lambda service, moves=tuple(moves): service.move_abs_many(moves))
+        self._command_token = self._submit(
+            lambda service, steps=plan.steps: _execute_steps(service, steps)
+        )
         if plan.steps:
             self.stepStarted.emit(plan.steps[0])
 
@@ -339,6 +366,20 @@ class PoseMover(QObject):
         self.state.plan = None
         self.failed.emit(message)
 
+    @Slot(int, object)
+    def on_command_finished(self, token: int, result: object) -> None:
+        """A rejected queued move must not later be reported as an arrival."""
+        if self.running and token == self._command_token:
+            self._command_token = None
+            if isinstance(result, MotionResult) and not result.ok:
+                self._fail(result.message)
+
+    @Slot(int, str)
+    def on_command_failed(self, token: int, message: str) -> None:
+        if self.running and token == self._command_token:
+            self._command_token = None
+            self._fail(message)
+
     # ---------------------------------------------------------------- progress
 
     def on_snapshot(self, snapshot: Snapshot) -> None:
@@ -364,12 +405,11 @@ class PoseMover(QObject):
             self._fail(f"{step.role} 报警 / alarm on {step.role}")
             return
 
-        # A linear role reads in millimetres, a rotary one in degrees; the service
+        # Arrival uses the same verified units as the planned physical target.
-        # converts lengths, the units module converts calibrated angles.
         if step.unit == "mm":
             travelled = self._service.to_mm(step.axis, state.dpos)
         else:
-            travelled = user_units_to_deg(step.axis, state.dpos)
+            travelled = self._service.to_deg(step.axis, state.dpos)
         tolerance = SETTLE_MM if step.unit == "mm" else SETTLE_DEG
 
         if not state.idle:
@@ -410,7 +450,7 @@ class PoseMover(QObject):
             if step.unit == "mm":
                 travelled = self._service.to_mm(step.axis, state.dpos)
             else:
-                travelled = user_units_to_deg(step.axis, state.dpos)
+                travelled = self._service.to_deg(step.axis, state.dpos)
             tolerance = SETTLE_MM if step.unit == "mm" else SETTLE_DEG
             arrived = state.idle and abs(travelled - step.target) <= tolerance
             if arrived:

apps/autocal/src/orisys_autocal/motion/service.py

@@ -43,6 +43,7 @@ from .units import (
     mm_to_user_units,
     safe_float,
     units_per_degree,
+    user_units_to_deg,
     user_units_to_mm,
 )
 
@@ -175,6 +176,7 @@ class MotionService:
         self._limits: dict[str, float] = dict(limits or {})
 
         self._spec: ConnectionSpec | None = None
+        self._last_axes: dict[int, AxisState] = {}
         self._bus = BusStatus()
         self._params: dict[int, AxisParams] = {
             axis: AxisParams() for axis in range(self.axis_count)
@@ -273,25 +275,62 @@ class MotionService:
         key = "max_travel_mm" if role in LINEAR_ROLES else f"max_{role}_deg"
         return safe_float(self._limits.get(key), 0.0)
 
-    def units_problem(self, role: str, axis: int) -> str:
+    def units_problem(self, role: str, axis: int, *, refresh: bool = False) -> str:
-        """Why a role cannot be commanded in its own unit, or ``""``."""
+        """Validate expected versus observed units, without changing either.
-        if role in LINEAR_ROLES:
+
-            return ""
+        ``refresh`` is only for the controller worker immediately before execution.
-        scale = units_per_degree(axis)
+        UI/planning checks use the last poll and never call the transport.
-        if not math.isfinite(scale) or scale <= 0:
+        """
+        expected = self.params(axis).units
+        if not math.isfinite(expected) or expected <= 0:
             return self._text(
-                f"{role} 用轴 {axis}，但该轴没有角度标定（用户单位/度）",
+                f"轴 {axis} 的 UNITS 无效", f"Axis {axis} has invalid expected UNITS"
-                f"{role} uses axis {axis}, which has no user-units-per-degree "
+            )
-                f"calibration",
+        if role not in LINEAR_ROLES and not math.isfinite(
+            units_per_degree(axis, units=expected)
+        ):
+            return self._text(
+                f"{role} 用轴 {axis}，但该轴没有当前 UNITS={expected:g} 对应的角度标定",
+                f"{role} uses axis {axis}, which has no rotary calibration for UNITS={expected:g}",
+            )
+        if refresh:
+            try:
+                observed = self._transport.get_units(axis)
+            except (ZAuxError, OSError) as exc:
+                return self._text(
+                    f"无法读取轴 {axis} 的 UNITS：{exc}",
+                    f"Cannot read axis {axis} UNITS: {exc}",
+                )
+        else:
+            state = self._last_axes.get(axis)
+            if state is None or not state.read_ok:
+                return self._text(
+                    f"轴 {axis} 的 UNITS 尚未成功读回",
+                    f"Axis {axis} UNITS has no successful readback",
+                )
+            observed = state.units
+        if (
+            not math.isfinite(observed)
+            or observed <= 0
+            or not math.isclose(expected, observed, rel_tol=1e-7, abs_tol=0.0)
+        ):
+            return self._text(
+                f"轴 {axis} 的 UNITS 不一致：配置 {expected:g}，读回 {observed:g}；未重新换算运动目标",
+                f"Axis {axis} UNITS mismatch: expected {expected:g}, read {observed:g}; motion was not rescaled",
             )
         return ""
 
-    def check_axes_move(self, targets: Mapping[str, float]) -> MotionResult | None:
+    def check_axes_move(
+        self, targets: Mapping[str, float], *, refresh_units: bool = False
+    ) -> MotionResult | None:
         """Refuse a coordinated pose move, or return ``None`` to allow it.
 
         ``targets`` is per role, in the role's own unit: millimetres for x / y / z,
         degrees for yaw / pitch.
 
+        ``refresh_units`` reads the current pulse equivalents and is worker-only.
+        It never writes them or rescales any already planned target.
+
         Every reason a move can be wrong is checked *before* the first axis is
         commanded. A pose move is several coordinated moves, and discovering at axis
         three that axis four is out of range would leave the machine stopped
@@ -321,7 +360,7 @@ class MotionService:
                     self._text(f"{role} 目标不是有效数字", f"{role} target is not a number")
                 )
             axis = self._axis_roles[role]
-            units_problem = self.units_problem(role, axis)
+            units_problem = self.units_problem(role, axis, refresh=refresh_units)
             if units_problem:
                 return MotionResult.refused(units_problem)
         for role, value in targets.items():
@@ -350,11 +389,11 @@ class MotionService:
         if axis is None:
             return math.nan
         if role in LINEAR_ROLES:
-            units = self.params(axis).units or self._units_per_mm
+            units = self.params(axis).units
             return mm_to_user_units(
                 value, units=units, pulses_per_mm=self._pulses_per_mm
             )
-        return deg_to_user_units(axis, value)
+        return deg_to_user_units(axis, value, units=self.params(axis).units)
 
     def set_language(self, language: str) -> None:
         self.language = language
@@ -399,6 +438,7 @@ class MotionService:
             return MotionResult.failed(code, message)
 
         self._spec = spec
+        self._last_axes.clear()
         # A controller may already have a BAS program running from a previous
         # session; adopt it rather than claiming the bus is uninitialised. The
         # adopted state is *not* marked verified: its globals are a latch, and
@@ -610,6 +650,7 @@ class MotionService:
                     )
                 )
 
+        self._last_axes.update({state.axis: state for state in states})
         return Snapshot(
             connected=True,
             spec=self._spec,
@@ -724,7 +765,6 @@ class MotionService:
                 home_status = 0
             self._home_done[axis] = home_status == 1
 
-        params = self.params(axis)
         return AxisState(
             axis=axis,
             enabled=transport.get_axis_enable(axis) != 0,
@@ -748,6 +788,8 @@ class MotionService:
             return MotionResult.refused(self._text("未连接控制器", "Not connected"))
         if not self._known_axis(axis):
             return MotionResult.refused(self._axis_range_message(axis))
+        # A partial write may already change UNITS even if speed/accel then fails.
+        self._last_axes.pop(axis, None)
         try:
             self._transport.set_units(axis, params.units)
             self._transport.set_speed(axis, params.speed)
@@ -979,7 +1021,7 @@ class MotionService:
         return MotionResult.success(self._text("回零已启动", "Homing started"))
 
     def _log_axis_readback(self, action: str) -> None:
-        """Read every axis and log it. Does not write parameters or start motion."""
+        """Log the last poll without issuing extra controller reads."""
         for axis in range(self.axis_count):
             self._log_command(action, axis, MotionResult.success("read"))
 
@@ -1000,23 +1042,17 @@ class MotionService:
     def _position_text(self, axis: int) -> str:
         """Commanded and measured position, for the command log.
 
-        Reads only. A failed read is part of the line rather than a second error,
+        These are cached poll values, not a synchronous post-command read. Logging
-        because the command result itself is what the caller is waiting on.
+        must not access the controller from the calling thread.
         """
-        if not self.connected:
+        state = self._last_axes.get(axis)
+        if not self.connected or state is None or not state.read_ok:
             return "dpos=unread mpos=unread status=unread enable=unread"
-        try:
         return (
-                f"dpos={self._transport.get_dpos(axis)} "
+            f"last_poll dpos={state.dpos} mpos={state.mpos} "
-                f"mpos={self._transport.get_mpos(axis)} "
+            f"status={state.status.raw} enable={state.enabled} "
-                f"status={self._transport.get_axis_status(axis)} "
+            f"atype={state.atype} units={state.units} speed={state.speed}"
-                f"enable={self._transport.get_axis_enable(axis)} "
-                f"atype={self._transport.get_atype(axis)} "
-                f"units={self._transport.get_units(axis)} "
-                f"speed={self._transport.get_speed(axis)}"
         )
-        except (ZAuxError, OSError) as exc:
-            return f"dpos=unread mpos=unread ({exc})"
 
     def _known_axis(self, axis: int) -> bool:
         return 0 <= int(axis) < self.axis_count
@@ -1099,11 +1135,19 @@ class MotionService:
 
     def to_mm(self, axis: int, user_units: float) -> float:
         """Displayed millimetres for a reading. Derived, never a measurement."""
-        units = self.params(axis).units or self._units_per_mm
+        if self.units_problem("x", axis):
+            return math.nan
+        units = self.params(axis).units
         return user_units_to_mm(
             user_units, units=units, pulses_per_mm=self._pulses_per_mm
         )
 
+    def to_deg(self, axis: int, user_units: float) -> float:
+        """Rotary readback in degrees, or NaN without matching calibrated units."""
+        if self.units_problem("yaw", axis):
+            return math.nan
+        return user_units_to_deg(axis, user_units, units=self.params(axis).units)
+
 
 def _replace_bus_type(bus: BusStatus, bus_type: BusType) -> BusStatus:
     return BusStatus(

apps/autocal/src/orisys_autocal/motion/units.py

@@ -34,6 +34,10 @@ ROTARY_UNITS_PER_90_DEG: dict[int, float] = {
     3: 29500.0,
 }
 
+#: Pulse equivalent at which both rotary user-unit scales were measured.
+#: Other equivalents require a new calibration; do not rescale commissioned moves.
+ROTARY_CALIBRATION_UNITS = 10.0
+
 
 def safe_float(text: object, fallback: float) -> float:
     """Parse ``text`` as a finite float, falling back on anything unusable.
@@ -80,25 +84,33 @@ def mm_to_user_units(
     return float(value) * float(pulses_per_mm) / float(units)
 
 
-def units_per_degree(axis: int) -> float:
+def units_per_degree(axis: int, *, units: float = ROTARY_CALIBRATION_UNITS) -> float:
     """User units per degree for a rotary axis, or NaN if not calibrated."""
     per_90 = ROTARY_UNITS_PER_90_DEG.get(int(axis))
-    if per_90 is None or per_90 <= 0:
+    if (
+        per_90 is None
+        or per_90 <= 0
+        or not math.isclose(units, ROTARY_CALIBRATION_UNITS, rel_tol=1e-7, abs_tol=0.0)
+    ):
         return math.nan
     return float(per_90) / 90.0
 
 
-def user_units_to_deg(axis: int, value: float) -> float:
+def user_units_to_deg(
+    axis: int, value: float, *, units: float = ROTARY_CALIBRATION_UNITS
+) -> float:
     """Convert controller user units to degrees for a calibrated rotary axis."""
-    scale = units_per_degree(axis)
+    scale = units_per_degree(axis, units=units)
     if not math.isfinite(scale) or scale == 0.0:
         return math.nan
     return float(value) / scale
 
 
-def deg_to_user_units(axis: int, degrees: float) -> float:
+def deg_to_user_units(
+    axis: int, degrees: float, *, units: float = ROTARY_CALIBRATION_UNITS
+) -> float:
     """Inverse of :func:`user_units_to_deg`."""
-    scale = units_per_degree(axis)
+    scale = units_per_degree(axis, units=units)
     if not math.isfinite(scale):
         return math.nan
     return float(degrees) * scale

apps/autocal/src/orisys_autocal/ui/window.py

@@ -857,6 +857,8 @@ class AutoCalMainWindow(QMainWindow):
         # hold the worker thread and a stop would have to wait for the move it is
         # meant to interrupt.
         self.mover = PoseMover(self.poller.service, self.poller.submit, self)
+        self.poller.commandFinished.connect(self.mover.on_command_finished)
+        self.poller.commandFailed.connect(self.mover.on_command_failed)
         self.mover.failed.connect(self._on_move_failed)
         self.mover.finished.connect(self._on_move_finished)
         self.mover.cancelled.connect(self._on_move_cancelled)
@@ -912,7 +914,7 @@ class AutoCalMainWindow(QMainWindow):
             if state is None or not state.read_ok:
                 return None
             if rotary:
-                return user_units_to_deg(int(axis), state.dpos)
+                return user_units_to_deg(int(axis), state.dpos, units=state.units)
             units = state.units or float(self.prefs.get("units_per_mm") or DEFAULT_UNITS)
             return user_units_to_mm(state.dpos, units=units)
 

apps/autocal/tests/test_motion_unit_guards.py

@@ -5,7 +5,15 @@ import math
 
 import pytest
 
-from orisys_autocal.motion.models import AxisParams, BusStatus, ConnectionSpec
+from orisys_autocal.motion.models import (
+    AxisParams,
+    AxisState,
+    AxisStatusBits,
+    BusStatus,
+    ConnectionSpec,
+    MotionResult,
+    Snapshot,
+)
 from orisys_autocal.motion.pose_move import PoseMover, plan_pose_move
 from orisys_autocal.motion.service import MotionService
 from orisys_autocal.motion.transport import DemoTransport
@@ -185,3 +193,86 @@ def test_raw_debug_moves_keep_the_existing_user_unit_contract():
     transport.set_units(2, 5.0)
     assert instance.move_abs(2, 90.0).ok
     assert transport.moves == [(2, 90.0)]
+
+
+@pytest.mark.parametrize("together", [False, True])
+@pytest.mark.parametrize("failure", ["refused", "exception"])
+def test_arrival_before_command_failure_never_reports_success(qt_app, together, failure):
+    instance, transport = service()
+    actions = []
+    mover = PoseMover(instance, lambda action: actions.append(action) or len(actions))
+    finished = []
+    mover.finished.connect(finished.append)
+    assert mover.start(plan_pose_move(instance, {"x": 0.0}, together=together)).ok
+    mover.on_snapshot(Snapshot(axes=(instance._last_axes[0],)))
+    assert not finished and mover.running
+
+    if failure == "refused":
+        transport.set_units(0, 5.0)
+        result = actions[0](instance)
+        assert not result.ok and "UNITS" in result.message
+        mover.on_command_finished(1, result)
+    else:
+        mover.on_command_failed(1, "read failed")
+    assert mover.state.failure and not mover.state.finished
+    assert not finished and not mover.running
+    assert transport.moves == []
+
+
+@pytest.mark.parametrize("together", [False, True])
+def test_only_matching_success_and_a_later_snapshot_allow_arrival(qt_app, together):
+    instance, _transport = service()
+    actions = []
+    mover = PoseMover(instance, lambda action: actions.append(action) or len(actions))
+    assert mover.start(plan_pose_move(instance, {"x": 0.0}, together=together)).ok
+    snapshot = Snapshot(axes=(instance._last_axes[0],))
+    mover.on_command_finished(99, MotionResult.success())
+    mover.on_snapshot(snapshot)
+    assert mover.running and not mover.state.finished
+    result = actions[0](instance)
+    assert result.ok
+    mover.on_command_finished(1, result)
+    assert mover.running, "a pre-acknowledgement snapshot was reused"
+    mover.on_snapshot(Snapshot(axes=(instance._last_axes[0],)))
+    assert mover.state.finished and not mover.running
+
+
+def test_each_sequential_axis_waits_for_its_own_command_success(qt_app):
+    instance, _transport = service()
+    actions = []
+    mover = PoseMover(instance, lambda action: actions.append(action) or len(actions))
+    assert mover.start(plan_pose_move(instance, {"x": 0.0, "y": 0.0})).ok
+    snapshot = Snapshot(axes=tuple(instance._last_axes[axis] for axis in (0, 1)))
+    mover.on_snapshot(snapshot)
+    assert len(actions) == 1 and mover.state.index == 0
+    result = actions[0](instance)
+    assert result.ok
+    mover.on_command_finished(1, result)
+    mover.on_snapshot(snapshot)
+    assert len(actions) == 2 and mover.state.index == 1
+    mover.on_command_finished(1, MotionResult.success())
+    mover.on_snapshot(snapshot)
+    assert mover.running and not mover.state.finished
+    result = actions[1](instance)
+    assert result.ok
+    mover.on_command_finished(2, result)
+    mover.on_snapshot(snapshot)
+    assert mover.state.finished
+
+
+@pytest.mark.parametrize("together", [False, True])
+@pytest.mark.parametrize("fault", ["alarm", "read"])
+def test_axis_faults_remain_visible_while_command_is_pending(qt_app, together, fault):
+    instance, _transport = service()
+    mover = PoseMover(instance, lambda _action: 1)
+    targets = {"x": 0.0, "y": 0.0} if together else {"y": 0.0}
+    assert mover.start(plan_pose_move(instance, targets, together=together)).ok
+    bad_axis = AxisState(
+        axis=1,
+        units=10.0,
+        status=AxisStatusBits(raw=512 if fault == "alarm" else 0),
+        read_ok=fault != "read",
+    )
+    mover.on_snapshot(Snapshot(axes=(AxisState(axis=0, units=10.0), bad_axis)))
+    assert not mover.running and not mover.state.finished
+    assert ("alarm" if fault == "alarm" else "read failed") in mover.state.failure

apps/autocal/tests/test_move_buttons.py

@@ -34,6 +34,8 @@ def _connected(make_window, *, confirm: bool = False):
     service = window.poller.service
     service._spec = object()  # noqa: SLF001 - connected, without opening anything
     service._bus = BusStatus(bus_type="ecat", init_status=1, total_axes=5)  # noqa: SLF001
+    # A ready physical-unit move also has a successful unit readback.
+    service._last_axes = {axis: service._read_axis(axis) for axis in range(5)}
     return window
 
 

apps/autocal/tests/test_pose_move.py

@@ -54,11 +54,13 @@ def make_service(**kwargs) -> MotionService:
     )
     service._spec = object()  # noqa: SLF001 - connected, without opening anything
     service._bus = BusStatus(bus_type="ecat", init_status=1, total_axes=5)  # noqa: SLF001
+    # Physical-unit planning requires observed units, just as the live poll supplies.
+    service._last_axes = {axis: service._read_axis(axis) for axis in range(5)}
     return service
 
 
 class FakePoller:
-    """Records submissions and runs them, so a plan's commands can be inspected."""
+    """Records submissions and explicitly acknowledges simulated worker results."""
 
     def __init__(self, service: MotionService) -> None:
         self.service = service
@@ -71,6 +73,9 @@ class FakePoller:
         # this test exists to check.
         return len(self.commands)
 
+    def acknowledge(self, mover: PoseMover) -> None:
+        mover.on_command_finished(len(self.commands), MotionResult.success())
+
 
 def reading(axis: int, dpos: float, *, idle: bool = True, alarm: bool = False) -> AxisState:
     return AxisState(
@@ -284,6 +289,7 @@ def test_an_execute_plan_moves_the_four_axes_together_and_leaves_z():
     assert len(poller.commands) == 1
     poller.commands[0](service)
     assert [axis for axis, _value in called[0]] == [3, 2, 0, 1]
+    poller.acknowledge(mover)
 
     mover.on_snapshot(
         snapshot_of(service, {0: 1000.0, 1: 0.0, 2: 0.0, 3: 0.0}, idle=False)
@@ -332,11 +338,13 @@ def test_the_mover_commands_one_axis_and_waits_for_it_to_arrive():
     plan = plan_pose_move(service, {"x": 2.0, "y": 1.0})
     assert mover.start(plan).ok
     assert len(poller.commands) == 1, "more than the first axis was commanded at once"
+    poller.acknowledge(mover)
 
     # x is at its target and idle -> the second axis goes out.
     mover.on_snapshot(snapshot_of(service, {0: 1000.0, 1: 0.0}))
     assert len(poller.commands) == 2
     assert mover.state.step.role == "y"
+    poller.acknowledge(mover)
 
     # y arrives -> the plan is done.
     mover.on_snapshot(snapshot_of(service, {0: 1000.0, 1: 500.0}))
@@ -349,6 +357,7 @@ def test_the_mover_waits_while_an_axis_is_still_moving():
     poller = FakePoller(service)
     mover = PoseMover(service, poller.submit)
     mover.start(plan_pose_move(service, {"x": 2.0, "y": 1.0}))
+    poller.acknowledge(mover)
     mover.on_snapshot(snapshot_of(service, {0: 990.0, 1: 0.0}, idle=False))
     assert len(poller.commands) == 1
     assert mover.state.index == 0
@@ -370,6 +379,7 @@ def test_a_long_yaw_is_not_cut_off_while_it_is_still_moving(monkeypatch):
     poller = FakePoller(service)
     mover = PoseMover(service, poller.submit)
     assert mover.start(plan_pose_move(service, {"yaw": 180.0})).ok
+    poller.acknowledge(mover)
     clock["t"] += 120.0
     mover.on_snapshot(snapshot_of(service, {3: 1_000.0}, idle=False))
     assert mover.running
@@ -383,6 +393,7 @@ def test_the_mover_fails_when_an_axis_stops_short():
     poller = FakePoller(service)
     mover = PoseMover(service, poller.submit)
     mover.start(plan_pose_move(service, {"x": 2.0, "y": 1.0}))
+    poller.acknowledge(mover)
     mover.on_snapshot(snapshot_of(service, {0: 10.0, 1: 0.0}))
     assert mover.running, "gave up before the stall grace elapsed"
     mover.state._idle_since = time.monotonic() - 10.0  # noqa: SLF001
@@ -408,6 +419,7 @@ def test_a_tolerance_accepts_an_axis_that_reports_its_final_position_late():
     mover = PoseMover(service, poller.submit)
     plan = plan_pose_move(service, {"x": 2.0, "y": 1.0})
     mover.start(plan)
+    poller.acknowledge(mover)
     # 1 unit inside SETTLE_MM of 1000 units for 2 mm.
     mover.on_snapshot(snapshot_of(service, {0: 1000.0 - 1.0, 1: 0.0}))
     assert len(poller.commands) == 2, "a step within tolerance was treated as a miss"