# Orisys AutoCal

Internal control application for the **5-axis calibration platform**, driving a
ZMotion ZMC bus controller (EtherCAT or RTEX) from the PC.

Replaces the vendor example program it was ported from:

    D:\orisys_ws\zmotion\Python64\例程9-总线控制运动

> **Internal use only.** AutoCal is not part of the customer installer. See
> "Do not ship this app" below.

## What it does

- **Connect** over Ethernet (with an IP scan), serial, PCI, local/simulated, or
  a built-in **demo** transport that needs no hardware and no DLL.
- **Initialise the bus** by downloading `ECAT.bas` or `RTEX.bas` to the
  controller, then follow the controller's own state machine to completion — or
  to a timeout, with the vendor's diagnostic hint.
- **Read axis state** for all five drives at once: enable, axis type, pulse
  equivalent, speed, acceleration, commanded and measured position (in user
  units *and* millimetres), axis status word, motion and homing state.
- **Move**: enable/disable, jog, absolute and relative moves, stop, stop-all,
  driver homing, clear a drive alarm. Every command is guarded — see below.
- **Exchange raw bus data**: EtherCAT object-dictionary (SDO) reads and writes,
  and RTEX parameters. Each family is enabled only when the controller reports
  that bus type.

## Run it

PySide6 only — Qt's LGPLv3 binding, so an internal closed-source tool needs no
licence purchase. (PyQt5 is GPLv3-or-commercial; the studio app moved to PySide6
for the same reason and no longer uses it.)

```powershell
# with the environment that already has PySide6 (Anaconda py310, for example)
$env:PYTHONPATH = "D:\orisys_ws\orisys-app\shared\src;D:\orisys_ws\orisys-app\apps\autocal\src"
python D:\orisys_ws\orisys-app\apps\autocal\run.py
```

Or with no controller attached at all:

```powershell
python .\apps\autocal\run.py --demo
```

`run.py` sets `ORISYS_APP_ID=autocal` before importing anything from
`orisys_app_shared`, so this app's `config/`, `preference.json` and `outputs/`
resolve to `apps/autocal/` rather than the studio's.

### Controller library

The ZMotion runtime is vendored at `shared/resources/zmotion/x64/` (see the
README beside it for provenance). Point `ORISYS_ZMOTION_DLL_DIR` at another
directory to use a different build — on a motion controller, silently loading
the wrong runtime version is the kind of fault that looks like a working machine
until it moves, so the override is authoritative: if it does not contain
`zauxdll.dll`, the app refuses to connect instead of quietly falling back.

One contract in `shared/src/orisys_app_shared/zmotion/client.py` is worth
knowing before touching it: `ZAux_Execute` **must** be given a reply buffer.
Passing `NULL` with a zero length is a write through a null pointer inside the
DLL — a native crash the worker thread cannot catch — and the buffer is also
how a refused online command explains itself, because `ZAux_Execute` returns 0
for a `RUN` whose file the controller does not have.

## Bring-up sequence

The vendor sequence, with the checks AutoCal's own state machine adds. P1 of
`docs/workflow.md` is this list in the workflow's vocabulary.

1. **Connect** (`eth` + the controller's IP). On success the app adopts any BAS
   program the controller is already running from a previous session instead of
   claiming the bus is uninitialised; `BUS_TYPE` is read immediately, and
   `Bus_InitStatus` on the first poll.
2. **Download only if the bus type is unknown.** `ECAT.bas` / `RTEX.bas` are
   chosen from `config/bas/` (the vendor requires a non-Chinese path) and
   written to ROM. A controller that still has the program needs no download.
3. **Wait for `Bus_InitStatus`** — `−1` running, `1` success, `0` failed —
   inside the vendor's 25 s window, then a timeout message naming the ZDevelop
   diagnostic (`?*ETHERCAT`).
4. **Re-initialise** re-runs the program without re-downloading it:
   `STOPTASK <task>` then `RUN "<file>",<task>`. The task number is
   `bas_task` in `preference.json` (default **4**, the task the vendor
   reference uses); the file name comes from this session's download, or from the
   remembered `bas_path` when the session adopted a running program (the
   controller does not report the name). The controller answers a `RUN` for a
   file it does not have with **code 0** and the refusal in its reply text, so
   that text is checked and shown rather than reported as an initialisation in
   progress.
5. **Enable, then jog.** Motion stays refused until step 3 reports success.

### Connection and error codes

`ZAux_*` returns two unrelated families of code, and they need different answers:

| Range | Family | What the operator should do |
|---|---|---|
| `0` | success | — |
| `20000–29999` | PC-library fault (handshake, socket, address) | check the cable/segment and the IP, make sure nothing else holds the connection, then retry. Frequently transient: a first open on a cold route can fail and succeed on the next attempt, which is why an Ethernet connect makes up to 3 attempts before reporting. |
| `30000+` | the auxiliary block `zauxdll2.h` documents | the message names it (`无应答`, `参数错误`, …) |
| anything else | the controller's own code | look it up in ZDevelop's table |

A **host-library** code is never sent to ZDevelop's table, because that table
cannot contain it. Observed at the bench: `20008` from `ZAux_OpenEth` on a first,
transient attempt that succeeded immediately afterwards.

## Safety model

The guards live in `motion/service.py`, not in the UI, so they hold whatever
calls them:

- **Motion is refused** while the bus is not initialised, while the axis is
  unknown, or on a non-finite target — with a reason, never a silent no-op.
- **Homing needs a configured mode.** The vendor example pre-fills `17`, which
  is one specific drive's mode; AutoCal starts at `0` and refuses, so the
  operator chooses for the drive in front of them instead of inheriting a number
  from another machine.
- **Homing is refused on RTEX**, as the vendor example itself does.
- **Disconnect stops the axes first** (the vendor program closes the handle and
  leaves the platform coasting).
- **SDO/RTEX are gated by the reported bus type**, so a write can never be aimed
  at the wrong family.
- **A failed read is marked, not zeroed.** `ZmotionValue.value_or_none` returns
  `None` on failure; nothing silently treats a failed read's zero as a position.

The displayed millimetre value is *derived* from the pulse equivalent
(bench-measured: `units=10` → 1000 user units = 2 mm). It is a display value,
not a calibrated length, and the UI says so.

## Layout

```text
apps/autocal/
  run.py                     # source-tree launcher
  config/
    preferences.default.json # shipped defaults
    locales/{zh_CN,en_US}.json
    bas/{ECAT,RTEX}.bas      # copies: the vendor needs a non-Chinese path
  src/orisys_autocal/
    main.py                  # logging, locale, theme, window
    preferences.py           # AutoCal's own preference schema
    motion/                  # Qt-free except poller.py (the Qt worker bridge)
      models.py errors.py units.py service.py transport.py poller.py
    ui/                      # window.py + one module per panel
  tools/                     # panel_check.py, panel_snapshot.py, preview_snapshot.py, layout_mockup.py
  tests/
```

`motion/poller.py` is the only place a controller call can originate. It owns
the DLL handle on its own thread, so the vendor library's blocking calls (a ROM
write, a bus scan) never freeze the window and the ctypes handle is never shared
between threads. The UI talks to it through signals only.

## Verify

Both work with no display, no controller and no DLL:

```powershell
python .\apps\autocal\tools\panel_check.py     # layout/theme/locale/gating checks
python .\apps\autocal\tools\panel_snapshot.py --demo --theme dark --out shot.png
python .\apps\autocal\tools\panel_snapshot.py --compare --out tabs.png   # one image per tab
python .\apps\autocal\tools\panel_snapshot.py --setup-dialog bus --out setup.png
python .\apps\autocal\tools\layout_mockup.py --out layout.png            # proposed layout, drawn
python -m pytest apps\autocal\tests            # offscreen suite
```

Connection and bus initialisation are used once per machine start-up, so they live
in a **modeless device-setup dialog** (`ui/device_setup.py`) rather than the rail:
the rail carries what is read while working — the axis readout and the collapsed
SDO/RTEX monitor. The dialog opens from the status strip's 设备设置 button, from the
connection/bus/init chips (each opens the tab that explains it) or from
文件 → 设备设置, and the strip keeps reporting the live state whether it is open or
shut.

`preview_snapshot.py` is the one tool that can photograph the **3D pane**, which
`panel_snapshot.py` cannot: the offscreen platform has no OpenGL context at all, so
the pane is empty in those shots. It needs the real platform plugin and a visible
window, and it writes either the pane alone or the whole page with the pane
composited in. What the view draws, and what each colour means, is in
[docs/finger-preview.md](docs/finger-preview.md).

`layout_mockup.py` is a **wireframe, not the application**: it paints the
proposed single-page layout with the shared theme tokens and imports nothing
from the app, so the layout can be reviewed and marked up without building the
panels. It draws the full page plus previews of the other workspace tabs in one
canvas, and `--page setup` draws the device-setup dialog over the page it opens
from.

`panel_check.py` builds the real window in both themes at 1440×900 and
1920×1080, asserts that no widget escapes its parent, that motion is
unreachable before the bus is initialised, that the SDO/RTEX panels follow the
reported bus family, and then runs a full simulated session from `ECAT.bas`.

The suite is written for **PySide6**. Where PySide6 is missing, the test modules
are skipped rather than failed: a broken environment should not look like a
broken application. `tests/test_binding_purity.py` enforces the binding policy
statically — no module may import PyQt5/PySide2/PyQt6, no module may use an
unscoped Qt enumerator (removed in PySide6), `shared/` may import PySide6 and no
other binding, and the controller interface must stay importable headless. The
studio app enforces the same rules for itself in
`apps/studio/tests/test_binding_purity.py`.

## Do not ship this app

AutoCal is an internal tool. It is deliberately **not** packaged by
`build/studio`, whose PyInstaller spec must not learn about the ZMotion runtime
DLLs, and it is not in the customer installer. The ZMotion SDK is vendor-supplied
hardware support software with its own terms; do not redistribute those DLLs
with a customer product.